Monday, 03 April 2017 13:25

Where do I start flying IMAC?

Written by
Rate this item
(0 votes)

So where do I start in Scale Aerobatics?

You can use any plane you like while competing in the basic class of IMAC. This can be a small petrol or glow powered plane, it can be electric and it doesn't have to be scale either. There is no size requirement either - it can be small or large.

There are however a few aspects of your plane that you should take into consideration. The first is to have a plane which runs reliably. There's nothing worse than stuggling to get your plane started, or having repeated engine or other failures. Sometimes this is simply from using cheaper products. The next aspect is whether the aircraft can do hammerheads (stall turns) and rolls. Your plane should be able to fly a vertical up line without dramatic loss of power, so make sure you don't try to fly IMAC with an under-powered plane.

Your expectations and abilities will change slowly but progressively as you begin to apply the discipline of aerobatic flying. If you are already flying at a club where someone flies IMAC then you are lucky. I'v never encountered and IMAC pilot who is not willing to help or give advice on how to get your plane IMAC-ready. Look at the competitions schedule to see where the closest one is to you so you can enter. Download the "BASIC Schedule and follow its sequence. Read the competition judging criteria. Who reads a manual? Very few initially, but you need to know what judges are looking for to downgrade your flying.

There's nothing wrong with feeling stressed about a competition and having people judge how you fly (they probably do anyway!). In IMAC everyone is pleased to help you improve your flying. So what better way to learn than by being judged? An adage we quote is that "experiencing one competition is like practicing for 6 weeks".

Finally establish a routine and stick to it during setting up your plane. Don't let others around you disturb your concentration during plane setup. Even the most experienced pilots have stories to tell about missing a wing bolt or not doing a pre-flight check. Always do a pre-flight check, and know your engine for startup. Having a routine will reduce the stress that exists at a competition. Experienced pilots might look relaxed, but they too are stressed and can miss out vital element of flight safety or checkups. Keep to a routine in preparing for landing.

How do I set my plane up the best to start?

This is a very simple process but is better rewarded with the more work and time you put into it. Getting a plane to perform predictably is the goal. Having a guide as to how much movement is ideal for different styles of flying. You can't imagine how complex it can get to make the complex manoeuvres look effortless and like you meant it. This will all be revealed as you gleam information from your fellow pilots and experts of all persuasions.

Every plane and how people like them is quite different but the following settings should be a reasonable benchmark as to not have a plane that is hard to control.

 Start with:-

  Elevator Rudder Aileron
Low Rate: 8-10 degrees 25 degrees 16 degrees
High Rate: 14 degrees 35 degrees 18 degrees
Exponential Rate: 30% 40% 30%

Once you have set your plane up to a manageable amount you can begin the trimming process. Trimming is ALL about reducing pilot load by making a plane fly straighter.

Peter Goldsmith who is a well-known and highly skilled Australian RC Aerobatic pilot wrote a detailed article on how to trim your plane. This information was then tabled and put into a trimming chart for ease of printing and taking to the field.

Trim your plane one step at a time from step 1 through to 10 to complete the trimming process. You can download this trim chart as well as an article explaining Peter's process in the "Downloads" section under "Self Help".  There is also another, similar article in there by Rich Fletcher.

written by Dan Carroll and Peter Bryner

Read 10846 times Last modified on Monday, 03 April 2017 15:37
Peter Bryner

I began R/C flying in about 2000 after a brief foray into RC modeling as a teenager.

I liked aerobatics and always tried to fly what I thought were the maneuvers. I saw Steve Coram fly at an open day at the KAMS field south of Perth. I was hooked, and it all looked so simple. Little did I realize what was to follow in order to fly at a fraction of his level of expertise.

I have been an active IMAC pilot in Western Australia, having joined the group at KAMS around 2003-4. I was inaugural President of Scale Aerobatics Western Australia (Inc) at the same time as the ASAA was being established in the east. In 2015 I served as stand-in President of the ASAA. Presently I am Secretary of the Scale Aerobatics Western Australia (Inc)

I have progressed slowly but steadily through the ranks despite some unexpected life events. I've attended interstate competitions in Katherine, Bendigo, Barossa and Yenda, until in 2016 I gained three promo points and won Advanced at the ASAA Nationals in Cootamundra.

What I've learned is that the first ingredient is a reliable aircraft which comes down to choosing good equipment and then putting it together so it won't fall apart the first violent maneuvere you make to correct that misbehaving thumb.

Secondly the plane needs to be appropriately trimmed and setup with rates that match your needs. Your setup will change as you need to execute more difficult and finessed figures.

Thirdly you need to read the rules and  the judging guide. Learn to judge by judging others as well as yourself. Modify your stick inputs, modify the travels to iron out your own mistakes. Downgrade what you see wrong according to the scoring criteria. Listen to fellow pilots about what they see, how they judge and appreciate the differences in perception. As you become a better pilot and a better judge your scores will improve despite the ever present inconsistent judging to which we humans are prone.

 I am in awe of the intensity and dedication one can dedicate to this sport - all to make flying look so easy.

We look froward to seeing you all at the WAGIN ASAA NATIONALS in SEPTEMBER 2017

f t g
Copyright © 2024 - xs web design